Surface Activator
Bridge Deck Membrane Surface Activator is a specially formulated single-component cleaner and surface activator. Bridge Deck Membrane Surface Activator is used to reactivate the surface of the Bridge Deck Membrane when incidental patching or over coating is required. Bridge Deck Membrane Surface Activator can be applied by roller or with a cotton rag.
Bridge Deck Membrane Surface Activator may be used when over coating or patching all Bridge Preservation™ rapid curing sealants and spray coatings systems.
| Property | Typical Value | |
|---|---|---|
| Color | Clear Liquid | |
| Odor | Mild Sweet Odor | |
| Specific Gravity @ 25°C | 1.08 | |
| Flash Point | 95°F | |
| Vapor Density (Air=1) | N.D. | |
| The value ranges stated above are based on system processing under laboratory conditions. Equipment configurations and/or field application conditions may produce variances in final system values. | ||
Patch Coat
Bridge Deck Membrane Patch Coat is a slow setting, 100% solids, two-component polymer product. Bridge Deck Membrane Patch Coat is used for incidental patching and touchup. The slower setting membrane allows material to be dispensed though duplex cartridges and finished by brush or trowel. Bridge Deck Membrane Patch Coat can be applied in temperatures down to -20°F without effect on setup time or curing, and can be applied at specified thickness in one continuous application.
Bridge Deck Patch Coat is a slow setting, 100% solids, two-component polymer product. Bridge Deck Patch Coat is used for incidental patching and touchup. The slower setting membrane allows material to be dispensed through duplex cartridges and finished by brush or trowel. Bridge Deck Patch Coat can be applied in temperatures down to -20°F without effect on setup time or curing, and can be applied at specified thickness in one continuous application.
| Property | Test Method | Typical Value |
|---|---|---|
| Solids Content | 100% | |
| Gel Time | >90 Seconds | |
| Tack Free | >2 Minutes | |
| Open to Light Traffic | 1 Hour | |
| Shore Hardness | ASTM D 2240 | 50 D |
| Elongation | ASTM D 638 | >250% |
| Tensile Strength (PSI) | ASTM D 638 | >2,000 |
| Tear Strength (PLI; Die C) | ASTM D 624 | >390 |
| Tabor Abrasion, mg. Loss (1000 gm, 1000 rev, H-18) | ASTM D 4060 | <250 |
| The value ranges stated above are based on system processing under laboratory conditions. Equipment configurations and/or field application conditions may produce variances in final system values. | ||
Patch Coat SC
Bridge Deck Patch Coat SC is a slow setting, 100% solids, single-component polymer product. Bridge Deck Patch Coat SC is used for incidental patching or membrane-to-membrane or membrane-to-substrate bonding.
Joint Adhesive
Spray Applied Joint Adhesive is a slow setting, 100% solids, two-component polymer product. Spray Applied Joint Adhesive is used with the Bridge Preservation Joint system to adhere both the joint flanges and seal joint overlaps. The slower setting adhesive membrane allows proper wetting and adhesion of joint materials before initial set. Spray Applied Joint Adhesive can be applied in temperatures down to -20°F without effect on setup time or curing, and can be applied at specific thickness in continuous application.
Bridge Deck Joint Adhesive is a superior high strength, elastomeric adhesive coating designed for use in the adhesion and sealing of the Bridge Preservation joint system.
| Property | Test Method | Typical Value |
|---|---|---|
| Solids Content | 100% | |
| Gel Time | >90 Seconds | |
| Tack Free | >2 Minutes | |
| Initial Cure | 1 Hour | |
| Shore Hardness | ASTM D 2240 | <50 D |
| Elongation | ASTM D 638 | >250% |
| Tensile Strength (PSI) | ASTM D 638 | >2,000 |
| Tear Strength (PLI; Die C) | ASTM D 624 | >390 |
| The value ranges stated above are based on system processing under laboratory conditions. Equipment configurations and/or field application conditions may produce variances in final system values. | ||
BD Grout
Bridge Deck Grout is a specifically formulated, 100% solids epoxy concrete restoration and rebuild product designed to repair heavily damaged concrete or to reconstruct areas where high strength, chemical resistance and quicker turn-around time is required.
Bridge Deck Grout is ideal for areas where traditional cementitous products are inadequate due to hydration requirements, length of cure time, lack of chemical resistance, or lower compression and flexural strength. Bridge Deck Grout can be formed, molded or shaped, making it ideal for vertical installation, reconstruction of key features, and repair of damaged concrete or new construction. Bridge Deck Grout is ideal in applications where concrete leveling is required.
| Property | Test Method | Typical Value |
|---|---|---|
| Working Time | Temperature Dependent | 20-30 minutes |
| Cure Time | Temperature Dependent | 8-12 hours |
| Mix Ratio | Volume | 3 Part A : 1 Part B |
| Solids Content | Weight | 100% |
| Compressive Strength | ASTM C 579 | 8,000-10,000 psi |
| Tensile Strength | ASTM C 307 | 4,000-5,000 psi |
| Flexural Strength | ASTM C 580 | 6,000-7,000 psi |
| Coefficient of Thermal Expansion | ASTM C 531 | 20x10-6 in/in°F |
| Density | 125 lbs./ft³ | |
| The value ranges stated above are based on system processing under laboratory conditions. Equipment configurations and/or field application conditions may produce variances in final system values. | ||
BD Butyl Tape PE
BD Butyl Tape PE is comprised of a UV resistant polymer backing and a butyl adhesive. It has silicone interleaving which is removed as the tape is applied.
BD Butyl Tape PE is designed to be used in conjunction with Bridge Preservation™ spray applied waterproofing products as a bond breaker.
| Property | Test Method | Typical Value |
|---|---|---|
| Adhesive | Modified Butyl | |
| Backing | Polyethylene | |
| Bonding Time | Immediate | |
| Peel Strength | 17 lbs./linear inch | |
| Tensile Strength | ASTM D822 | 4,821 psi |
| Thickness | ASTM D1000 | 30 mils |
| Elongation | ASTM D822 | 900% |
| The value ranges stated above are based on system processing under laboratory conditions. Equipment configurations and/or field application conditions may produce variances in final system values. | ||
BD Butyl Tape FR
BD Butyl Tape FR is a butyl rubber adhesive tape with a polyester fabric backing.
BD Butyl Tape FR is designed to be used in conjunction with Bridge Preservation™ spray applied waterproofing products to provide reinforcement as required.
| Property | Test Method | Typical Value |
|---|---|---|
| Adhesive | Modified Butyl | |
| Backing | Polyester | |
| Bonding Time | Immediate | |
| Tensile Strength | 790 psi, average | |
| Peel Strength | 17 lbs./linear inch | |
| Thickness | ASTM D1000 | 25 mils |
| Elongation | ASTM D822 | 560%, average |
| The value ranges stated above are based on system processing under laboratory conditions. Equipment configurations and/or field application conditions may produce variances in final system values. | ||
BD Concrete Sealer WB
BD Concrete Sealer WB is a color stable, waterborne coating used for coating or sealing. It may be applied directly to properly prepared concrete and steel surfaces, or over other Bridge Preservation products to provide long-term color stability when required. When fully cured, BD Concrete Sealer WB provides excellent UV weathering characteristics and is abrasion resistant and chemical resistant.
BD Concrete Sealer WB is an abrasion resistant and color stable coating system designed to enhance gloss and provide additional UV resistance and stability to other Bridge Preservation products.
| Property | Test Method | Typical Value |
|---|---|---|
| VOC | Theoretical | 0 | Solids Content | Theoretical | 62% | Pot Life (at 77°F with recommended distilled water reduction) | 1 Hour | Tack Free | ASTM D1640 | 1-2 Minutes | Tensile Strength | ASTM D638 | 4,000 psi, minimum | Elongation | ASTM D638 | 3%, minimum | Tear Strength | ASTM D624 | 150 pli, minimum | Taber Abrasion, mg. wt. loss (1,000 g, 1,000 revs, H-18) | ASTM D4060 | 260 | Taber Abrasion, mg. wt. loss (1,000 g, 1,000 revs, C-17) | ASTM D4060 | 25 |
| The value ranges stated above are based on system processing under laboratory conditions. Equipment configurations and/or field application conditions may produce variances in final system values. | ||
